DISCLAIMER: You may notice there are a lot of over-used keywords or phrases as well as English that seems a little off. This is because these articles are used to feed our AI Robot (Ira) and she needs the data to be structured in a certain way.
This is the digital setup instructions for the Black Series Smart On/Off Switch on the Hubitat platform.
Navigating the Instructions
Please click on any of the sections in the Table of Contents to get started. We recommend working your way down as it follows an intentional flow that is user friendly and hub/gateway specific. As always, any questions, please see the Additional Resources links section or submit a ticket, we’re happy to help.
Quick Setup Instructions
Follow these if you have already installed the On/Off switch before and are just looking for some quick pairing instructions. If this is your first time installing the On/Off switch, please skip this section and work your way through the various sections below starting with the Prerequisites.
This section assumes the following:
You’ve installed the Device Driver
You’ve wired the switch and it works manually
Let’s begin:
Make sure your switch LED is lit up blue
Open up your Hubitat Web App and click on the, “Devices” tab
Click, “Add Device”
Then under, "Add device manually:", click on, "Z-Wave"
Click on, "Start Z-Wave Inclusion"
Tap on the config/favorites button three (3) times until the LED Bar starts to pulse blue
Hubitat should then search for, find and let you know that a, "Z-Wave device" was added
Click on, "Setup"
Hubitat should then search for, find and let you know that a device was added
Feel free to label the device and, if applicable, add it to a room
Video Demonstration
Video Demonstration
If your LED bar refuses to pulse blue, you may have to factory reset your device by holding down on the top of the config/favorites button for 20 seconds until the LED Bar turns red and let go as shown below in the GIF.
Video Demonstration
Video Demonstration
Prerequisites
The only prerequisite to pairing this bulb is the following:
Installation of the Device Driver
While this switch will also pair without it, for full functionality, you’ll want to install the Device Driver.
Device Driver Installation
To install the Device Driver, please follow the instructions below:
Open up your Hubitat web app and click on, "Drivers Code" in the menu (you may have to click on, "Advanced" if you don't see this option)
Click on, "+ New Driver"
Click on, "Import" and a box should appear that says, "Import Code from Website" and it will ask you for a URL
Paste the following URL (https://raw.githubusercontent.com/InovelliUSA/Hubitat/master/Drivers/inovelli-switch-lzw30.src/inovelli-switch-lzw30.groovy) into the section titled, "Insert URL to Import Text into Code Editor" and click, "Import" (followed by, "OK" when asked if you want to override the text in the editor)
Click, "Save"
Now when you pair your switch, it should automatically pick up the Device Driver. Feel free to move onto the next section of the Setup Instructions below.
Installation Instructions
Before setting up your switch within Hubitat, you will have to manually install your switch in the wall and have it powered up. In order to do that, you (or your licensed electrician) will need to follow our Wiring Instructions which can be found below:
Pairing Instructions
The below instructions assume you have installed the Device Driver prior to pairing. Please follow the instructions below to include/pair your Black Series On/Off Switch.
Open your Hubitat Web App and go to the, "Devices" tab
Press the (+ Add Device) button at the top right of the screen
Under, "Add device manually:", click on, “Z-Wave”
Click on, "Start Z-Wave Inclusion"
While your Hubitat hub is scanning, tap on the config/favorites button three times consecutively.
Hubitat will then continue to search for your Inovelli switch and, if successful, will let you know that the device was found and ultimately added
You can change the name of your switch by clicking where it says, "Label this device" and then clicking, "Save"
To view your device and change any of the parameters, click on, "View device details"
Once your switch is successfully paired, check to make sure you have basic functionality of your switch by turning it on/off and dimming up/down.
Advanced Feature Setup
This switch is packed with features and most of them come directly from this community. They've been debated back and forth, added to wishlists, and talked about tirelessly over the years.
Below we will provide a link to all the parameters and show you how to change them from within Hubitat and then we'll go into some of the advanced features and explain how to set them up in Hubitat.
Parameter Explanations
You will need to install an Edge Driver prior to accessing any of these features from within the app. Instructions can be found here: Device Driver Installation
To find all the parameters, please follow these steps:
Open your Hubitat Web App and go to the, "Devices" tab
Find your Black Series On/Off Switch and click on it
Scroll down to where it says, "Preferences" - here is where all the parameters are listed out and can be changed via the drop-downs
For a list of the most up-to-date parameters and the firmware version they are associated with, please visit the Black Series On/Off Switch Parameter Page
Z-Wave Associations
Z-Wave Associations is when two or more Z-Wave products communicate directly with one another without the need to communicate with a hub. There are two main benefits of utilizing Z-Wave Associations: speed & local control.
From a speed standpoint, cutting out the middle-man (hub) can save precious milliseconds or even seconds depending on your cloud and/or processing power off your hub. Whereas from a local control standpoint, if your hub goes does down and cannot communicate, your products can still talk to each other.
To setup Z-Wave Associations with your Hubitat Hub, please see this article: Setting Up Z-Wave Associations • Hubitat